Imagesetter vs Inkjet comparison

[Ron-san]

Here is a question for all you techincal types.
Imagesetters will print at a resolution of up to 3600, possibly 4000 dpi. My Epson 4000 prints at a resolution of 2880 dpi. But 2880 is the resolution for each individual ink, isn't it. If I use Quadtone RIP to make the printer print with nearly equal amounts of all seven inks, and if each ink is printing with a resolution of 2880 dpi, how many effective dots per inch am I getting? 2880x7 ???? If this line of thinking is correct, it would seem that a modern inkjet printer would blow any image setter out of the water, in terms of resolution? What am I missing?
Cheers, Ron-san

[clay]

I can't speak to the technical reasons, only the results. I have done a lot of imagesetter negatives, and even an imagesetter neg output at 2400dpi prints sharper than a 2880 inkjet neg. Whether this is due to microscopic ink spreading or what, I can't say. But the imagesetter negs have more print acuity than the inkjet versions printed from the same file. But they cost a whole lot more.

[Ron-san]

I can't speak to the technical reasons, only the results. I have done a lot of imagesetter negatives, and even an imagesetter neg output at 2400dpi prints sharper than a 2880 inkjet neg. Whether this is due to microscopic ink spreading or what, I can't say. But the imagesetter negs have more print acuity than the inkjet versions printed from the same file. But they cost a whole lot more.

Clay-- Actually, I am not much worried about sharpness or acuity. I am wondering how they compare in tonal smoothness. Would an inkjet printer printing with all seven inks show less dot pattern than an imagesetter printing with one ink?? I have never used an imagesetter and have no reference for comparison. Thanks, Ron-san

[clay]

As far as smoothness goes - with the imagesetter negatives a lot depends on the curve you use and the operator of the machine. I used one outfit for years and the Fokos curve and I got beautiful results. Then that operator left, and I got some pretty substandard results. In fact, this episode has made me far more interested in getting the inkjet negatives to the same point that I had the imagesetter negs.

My intution is that a properly curved inkjet negative will probably be smoother in the highlight tones than an imagesetter. But that is pure seat-of-the-pants SWAG at this point. I have not done a direct comparison with your quadtone negs and an imagesetter neg of the same image. Need to create an eight day week.

FWIW, I used that 2200 curve you downloaded to the site here and I got some pretty good results. Actually results so good that I question whether I ought to try refining them or just use them as-is and make a bunch of prints. I can't wait to see the book.

[Helen Bach]

Here is a question for all you techincal types.
Imagesetters will print at a resolution of up to 3600, possibly 4000 dpi. My Epson 4000 prints at a resolution of 2880 dpi. But 2880 is the resolution for each individual ink, isn't it. If I use Quadtone RIP to make the printer print with nearly equal amounts of all seven inks, and if each ink is printing with a resolution of 2880 dpi, how many effective dots per inch am I getting? 2880x7 ???? If this line of thinking is correct, it would seem that a modern inkjet printer would blow any image setter out of the water, in terms of resolution? What am I missing?
Cheers, Ron-san

But how many dots are required for a pixel if you are printing something that isn't just black or white? The true resolution might be a tenth of the nominal dpi. That's why a Lightjet at 400 ppi can look sharper than an inkjet at 2880 tpi (thingybobs per inch). It's easy enough to check - just print a test pattern with features one pixel wide and see how well it prints at different dpi settings. You might find different optimum values for QTR vs the Epson driver, and you might find that the horizontal and vertical optima are different with QTR - ie one value gives the best horizontal resolution and another value gives the best vertical resolution. QTR and the Epson driver handle the issue in different ways.

Best,
Helen

[L Gebhardt]

Here is a question for all you techincal types.
Imagesetters will print at a resolution of up to 3600, possibly 4000 dpi. My Epson 4000 prints at a resolution of 2880 dpi. But 2880 is the resolution for each individual ink, isn't it. If I use Quadtone RIP to make the printer print with nearly equal amounts of all seven inks, and if each ink is printing with a resolution of 2880 dpi, how many effective dots per inch am I getting? 2880x7 ???? If this line of thinking is correct, it would seem that a modern inkjet printer would blow any image setter out of the water, in terms of resolution? What am I missing?
Cheers, Ron-san

I don't think theory and reality are going to always be the same when comparing output methods. From what I have seen image setters produce sharper looking negatives than inkjets. Continuous tone film recorders capture much more fine detail than either, but may not look sharper than an image setter.

Keep in mind that an image setter's resolution is for only black and white dots. Thus to get 256 tones you need a 16x16 square of pixels, so your real resolution for a 3600dpi image setter is 3600/16 or 225ppi (image pixels per inch). Inkjet printers are similar and usually have real resolutions of 360ppi or maybe 720ppi. Continuous tone devices such as film recorders, lambdas, dye sub printers and LED printers have dpi measurements that directly correspond to ppi.

[Ron-san]

I don't think theory and reality are going to always be the same when comparing output methods. From what I have seen image setters produce sharper looking negatives than inkjets. Continuous tone film recorders capture much more fine detail than either, but may not look sharper than an image setter.

Keep in mind that an image setter's resolution is for only black and white dots. Thus to get 256 tones you need a 16x16 square of pixels, so your real resolution for a 3600dpi image setter is 3600/16 or 225ppi (image pixels per inch). Inkjet printers are similar and usually have real resolutions of 360ppi or maybe 720ppi. Continuous tone devices such as film recorders, lambdas, dye sub printers and LED printers have dpi measurements that directly correspond to ppi.

Thanks to all for the replies. I thought my way of looking at the matter was way to simplistic. Ron-san

[bob carnie]

I am interested in this very thing, I would like to make very large separation negatives on FP4 or equivalent film for alt printing.
I think the film from the lambda will be very good for this purpose. Right now I image at 400ppi and when making a 30x40 cibachrome*very high gloss* louping the print only shows me film grain and not a pixelation that I suspected.
Therefore I believe that if one prints onto a rag paper with platinum and maybe a colour gum over hit the results would be nothing short of spectacular.
At this point I am gathering my pennies to buy a 30inch roll of film from Ilford or Jand&C and hope to see if my hunch is correct.

[bradhi]

I have tried both imagesetter and inkjet negatives.

Imagesetter negatives:
You need to find a good imagesetter lab - many don't use the newer RIPs to get super high resolutions - and most are not consistent enough to get reliable results.
Expensive per negative - about $50 for a 20" x 30" neg. - but you can group negatives.
Sizes go up as large as 30"x40" (or maybe larger)
Takes time - you need to drop of the files and come back to pick up the negatives.
Imagesetter negatives are really just clear film and black dots - at very high resolutions. These work fine, but they don't work like traditional negatives (that have grey values). It can be diffucult to tweak your prints - but adding a but more time for example.
I think these are best for production type work. If you have a specific process that you want to print professionally, you can make a set of negatives and then print away on these.
Printing onto silver gelatin produces noticable dots under a loop.

Inkjet negatives:
These can be very sharp.
You can print negatives right at your desktop.
Your prints are limited by the size of your printer.
It is easy to tweak your prints and experiment.
I'd strongly recommend using inkjet negatives to start - and likely you'll never want to go to using an imagesetter.

Hope this is useful

[jd callow]

It would seem that you could layer image setter produced negs which would conceivably increase the tonal range (like a duo tone). it would also seem likely that you could do this with stochastic patterns which would help alleviate registration issues and further increase the tonal range and the ability to layer more negs.

Just a thought...